You are here: Home > AutoLoad Parts > FL- Single 1.25" Inlet Filter Bag Top
Sort By:
Page of 2
(3/8"POLYFLO) 3/8"POLYFLO TUBING
(3/8"POLYFLO) 3/8"POLYFLO TUBING
Our Price: $2.40

SPECIFY DESIRED LENGTH
NORMALLY PROVIDED IN 10FT SECTION
more info
(SG-ORING BOT) FOR BOTTOM END BELL
(SG-ORING BOT) FOR BOTTOM END BELL
Our Price: $4.50

more info
(HP-CONE GASK) RED GASKET ONLY
(HP-CONE GASK) RED GASKET ONLY
Our Price: $8.30

more info
(FL-TOP GASKT) FL TOP GASKET
(FL-TOP GASKT) FL TOP GASKET
Our Price: $9.90

more info
(1.25"HOSE W) 1.25"HOSE W WIRE REIN. HOSE
(1.25"HOSE W) 1.25"HOSE W WIRE REIN. HOSE
Our Price: $21.00

COLOR OF HOSE SUBJECT TO STOCK AVAILABILITY.
SPECIFY DESIRED TOTAL LENGTH IN FEET. IF YOU NEED TWO 10FT HOSES, ORDER 20FT OF HOSE.
HOSE CLAMPS SHOWN ABOVE ARE NOT INCLUDED BUT CAN BE PURCHASED SEPERATELY
STOCKED IN 10FT LENGTHS, CUSTOM LENGTHS MAY DELAY SHIPMENT.
more info
(SG-ORING TOP) FOR TOP END BELL
(SG-ORING TOP) FOR TOP END BELL
Our Price: $22.00

more info
(FILT.HD ASY) FILTER HOLD DOWN ASSY
(FILT.HD ASY) FILTER HOLD DOWN ASSY
Our Price: $23.00

more info
(SG-SUPRTROD) SUPPORT ROD-SIGHT GLASS ASSY
(SG-SUPRTROD) SUPPORT ROD-SIGHT GLASS ASSY
Our Price: $31.00

more info
(FL-SCREEN) TOP SCREEN, 20 MESH SCREEN
(FL-SCREEN) TOP SCREEN, 20 MESH SCREEN
Our Price: $33.00

more info
(SG-SEN BRACK) SENSOR BRACKET FOR JR
(SG-SEN BRACK) SENSOR BRACKET FOR JR
Our Price: $58.00

Sensor bracket for Original Autoload more info
(SG-1000) SIGHT GLASS TUBE
(SG-1000) SIGHT GLASS TUBE
Our Price: $67.00

more info
(FL-BAG FILTE) 5 MICRON FILTER BAG W/CLOSING SLIDE
(FL-BAG FILTE) 5 MICRON FILTER BAG W/CLOSING SLIDE
Our Price: $98.00

This bag is approximately 28" in overall length. more info
(AL-BP-A) AUTOLOAD STANDARD BASE PLATE
(AL-BP-A) AUTOLOAD STANDARD BASE PLATE
Our Price: $100.00

5.75" X 5.75" - CUSTOMER DRILLS DESIRED MOUNTING PATTERN
OUTPUT IS FLUSH WITH FLANGE
ADDITIONAL BASE PLATES ARE AVAILABLE TO HAVE EXTENDED OUTPUTS FOR HOPPER MOUNTING.
more info
(SG-ENDBELL T) SMALL END BELL TOP
(SG-ENDBELL T) SMALL END BELL TOP
Our Price: $118.00

more info
(AC-5125 STEE) STANDARD REINFORCED 1.25" ACCELERATOR
(AC-5125 STEE) STANDARD REINFORCED 1.25" ACCELERATOR
Our Price: $132.00

Aluminum construction with steel insert at venturi to extend life.
Suitable for most semi-abrasive materials.
Replaces AC-5125 as the new standard 4/2016
more info
(AC-5125 SUPE) SUPER 1.25" ACCELERATOR ASSEMBLY
(AC-5125 SUPE) SUPER 1.25" ACCELERATOR ASSEMBLY
Our Price: $141.00

Aluminum construction.
Suitable for most non-abrasive materials.
Used when conveying in longer distances or material has a higher than average bulk density.
more info
(WN-6125 STL) REINFORCED 1.25" WAND ASSEMBLY
(WN-6125 STL) REINFORCED 1.25" WAND ASSEMBLY
Our Price: $213.00

Aluminum construction with steel insert at venturi to reduce wear.
Suitable for most semi-abrasive materials.
As of 8/1/2016 this is the standard Autoload Wand.
more info
(WN-6125 SUPE) SUPER 1.25" WAND ASSEMBLY
(WN-6125 SUPE) SUPER 1.25" WAND ASSEMBLY
Our Price: $226.00

Aluminum construction.
Suitable for most non-abrasive materials.
Used when conveying in longer distances or material has a higher than average bulk density.
more info
(SENSOR ASSY) SENSOR ASSEMBLY W/PLUG
(SENSOR ASSY) SENSOR ASSEMBLY W/PLUG
Our Price: $294.00

more info
(MG-3500) MAGNET ASSY FOR AUTOLOAD SERIES I
(MG-3500) MAGNET ASSY FOR AUTOLOAD SERIES I
Our Price: $393.00

Autoload's rare-earth magnets mount externally without impeding material flow.
Clean-out by simply lifting the loader off it's mount, twist the magnet away from the sight glass and let the contaminates fall away.
NOT FOR USE WITH AUTOLOAD JR, OR JRII
more info